|
|
Post by 2 Dogs on Feb 4, 2012 14:05:40 GMT -5
If you and Subsonic can drum up about 10 orders Im quite sure we can get them out here specifically for BFRs pretty shortly.....
|
|
|
|
Post by bigbores on Feb 4, 2012 14:15:58 GMT -5
I would want 3, my other BFR's have Gary's replaceable front site system.
would need to be a min .600" height from the center of the bottom to the top, (just measured my 475L front site).
|
|
|
|
Post by subsonic on Feb 4, 2012 15:33:36 GMT -5
OD on my .475 BFR barrel is .820"
Now you just need to know where to put the screw and size of the hole.
My BFR screw hole is .750" from the end of the barrel to the center of the hole.
|
|
|
|
Post by subsonic on Feb 4, 2012 15:39:42 GMT -5
Put me down for one for sure (maybe 2) for a BFR if you make them and maybe a single six after you compare heights for the drift sights.
|
|
|
|
Post by tas6691 on Feb 4, 2012 16:18:12 GMT -5
I wonder if this would fit an early 3rd gen New Frontier after the barrel is cut.....put me down for one and I'll let ya know after I try.
I'm in for one.
|
|
|
|
Post by 2 Dogs on Feb 4, 2012 16:19:05 GMT -5
So thats 5 for the BFRs.
Bigbores, PM sent.
|
|
|
|
Post by bigbores on Feb 4, 2012 17:47:06 GMT -5
So thats 5 for the BFRs. Bigbores, PM sent. Back at you! |
|
|
|
Post by boxhead on Feb 5, 2012 8:11:43 GMT -5
Ed, the blade does have a angle, but there is no sense is taking them any further. Some guys will want gold bars, some guys want serrations, some guys might want a bead etc..... Yes, of course. Just being a little selfish. ;D No need for gold bars or beads on a .22 for me. If I hadn't already tweaked my BFR I would be in for one for sure. Assume they would work on the 22 semi-auto's too? |
|
|
|
Post by subsonic on Feb 5, 2012 9:20:24 GMT -5
I would want 3, my other BFR's have Gary's replaceable front site system. would need to be a min .600" height from the center of the bottom to the top, (just measured my 475L front site). It seems like there is a taller sight on some of the guns, like the short .44 mags. It's hard to file a sight taller. I have tried! |
|
otto
.240 Incinerator
Posts: 20
|
Post by otto on Feb 5, 2012 9:43:10 GMT -5
Put me down for 2 for BFR's
otto
|
|
|
|
Post by 2 Dogs on Feb 5, 2012 10:00:36 GMT -5
Tas6691, I need to know if you intend to install your front sight with a screw or if you intend to silver solder it on?
Otto, got it, thanks.
|
|
|
|
Post by 2 Dogs on Feb 5, 2012 10:05:37 GMT -5
Ed, I have to pull out my heavy barrel MkII and check the radius. I believe it will be a bit different, but if we can cut it, that sight will not only fit the MkII but those heavy barrel 10" SBH guns too. Will advise.
|
|
|
|
Post by 2 Dogs on Feb 5, 2012 10:16:28 GMT -5
Subsonic, remind me to buy you a beer! You were absolutely right. I didnt realize so many BFR guys were getting short changed. I figured far more Single Six guys would want a sight. As it sits right now, they are tied!!
|
|
|
|
Post by AxeHandle on Feb 5, 2012 11:12:50 GMT -5
The BFR guys are coming out of the closet!  Since I have BFRs and plans for more I'd better be scraping up pennies for a few BFR blades too... The 500 JRH I have planned will need one for sure! |
|
|
|
Post by subsonic on Feb 5, 2012 12:25:58 GMT -5
Ok. I like beer.
Let me know on the drift sight thing. That little gun shoots dang good too. 1.5" @25yds with CCI Blasers.
|
|
Since I have BFRs and plans for more I'd better be scraping up pennies for a few BFR blades too... The 500 JRH I have planned will need one for sure!