|
Post by hoover on Apr 21, 2015 21:26:51 GMT -5
You'll be glad you did! I believe that will make it 19 molds!
|
|
|
Post by Markbo on Apr 21, 2015 21:36:44 GMT -5
I want to get in on this and have a couple questions. My use will be .32 H&R only and I will be PCing all. Will I be able to use the crimp groove in my Single Six? Since I am PCing and .32 H&R velocities I dont think I need a gas check. Is the plain base just as accurate? Is the large HP or Penta HP proven one more accurate than the other?
I know, I know every gun is different but I am just hoping there has been some patterns identified.
Thanks Mark
|
|
sal
.30 Stingray
Posts: 315
|
Post by sal on Apr 21, 2015 23:01:36 GMT -5
I want a four hole, pb but I can never log on to castboolets. Need help in ordering a mold. I have the sledgehammer and Love it
|
|
|
Post by 2 Dogs on Apr 21, 2015 23:12:37 GMT -5
That's easy Sal. Just post your info here and we can cut and paste it.
|
|
sal
.30 Stingray
Posts: 315
|
Post by sal on Apr 21, 2015 23:38:11 GMT -5
Thanks Ferman. I want 4 hole pb with hp pins nascarsal@aol.com
|
|
ethang
.240 Incinerator
Posts: 48
|
Post by ethang on Apr 22, 2015 7:40:58 GMT -5
Thanks for the advice gentlemen. I put in for a 4 banger with HP and blank pins. I have been on the fence for years about starting to cast. Thanks for the shove.
|
|
|
Post by 2 Dogs on Apr 22, 2015 7:48:00 GMT -5
Thanks Ferman. I want 4 hole pb with hp pins nascarsal@aol.com Ok Sal, we got you all fixed up.
|
|
ryan
.30 Stingray
Posts: 402
|
Post by ryan on Apr 22, 2015 9:00:32 GMT -5
Just signed up for two.
You guys are costing me a lot of money...but the smile hardly ever leaves my face! And despite my best efforts, PCing is probably the next project!
|
|
|
Post by hoover on Apr 22, 2015 9:17:22 GMT -5
We have sal and ryan signed up! You will have no regrets gentlemen! It is a great mold and design!
Markbo, the Miha 115 gr was made for the .32 H&R. It will fit like a condom in your single six, with a little room left at the tip. Also, do you want PB or GC for your mold? As to accuracy with penta vs. round HP, I have no clue. I'm guessing if there was, your gun would never be able to tell the difference. Could be a good test for you to do when you get your mold.
27 MOLDS AND COUNTING......
|
|
|
Post by sheriff on Apr 22, 2015 11:45:51 GMT -5
Markbo, as an addition to Jeff's post, this bullet looks very similar to Lyman's 311008 which is a plain base bullet developed for the .32-20/.32WCF. (My eyesight is not what it used to be, so I may be mistaken on the similarity) I've loaded this bullet (311008)in the crimp groove, (COL 1.418)and it fits my .32 H&R single-six with room to spare. It's the one, bullet and loaded round, in the center. Cast of my alloy it weighs 114.8grs. The left bullet is a 100gr Keith and the right one is Fermin's Sledgehammer.
|
|
|
Post by Markbo on Apr 23, 2015 17:28:42 GMT -5
Thanks for that Sheriff and Tank. Got my order in. After I finish off the last of the store bought 100gr bullets I have I might to get a mold for that too.... what mold is your 100gr Keith out of Sheriff? Looks like a dandy
|
|
|
Post by sheriff on Apr 23, 2015 19:36:27 GMT -5
Markbo, it's an Accurate molds 314-100, brass 4 cavity.
(I was checking Accurate's catalog today for another .32 mold and noticed their mold design #'s have changed. This mold is now listed as a 31-105K)
|
|
|
Post by Markbo on Apr 27, 2015 11:38:09 GMT -5
Thanks Sheriff....might have to get one of them too. I didnt see the.option on their website...does accurate offer HP pins?
|
|
|
Post by sheriff on Apr 27, 2015 20:15:43 GMT -5
No,sir, they don't offer HP pins, unfortunately.
|
|
|
Post by hoover on Apr 27, 2015 20:26:20 GMT -5
31 molds and counting.......
|
|