caryc
.375 Atomic
Posts: 1,040
|
Post by caryc on May 25, 2011 14:26:35 GMT -5
Being a grip maker I've been contacted four or five times to make BFR grips for someone. The callers have invariably heard the same thing most of us have. Super Blackhawk grips will fit a BFR. I don't make grips on "kind of" or Sort of" fit info. We've all heard that rumor. Well, I can now definitely say it's a rumor. I finally got a customer that was willing to send me his BFR grip frame. You can see the two frames in the first picture. The BFR on the left looks a little beefier than the SBH frame but it's an illusion. The BFR on the left weighs 8.9 oz. and the SBH weighs 9.5 oz. As for the fit, you can see a stock SBH grip on the BFR frame. The grip is on the pin and the top and back strap fit as well as you'd expect a stock grip to fit. All the difference is clearly visible on the front strap and where it meets the cylinder frame. So, if you believe the rumors and order a set of SBH grips for your BFR, this is how you can expect them to fit. Mystery finally solved, well at least for me anyway.
|
|
|
Post by bigbores on May 25, 2011 14:55:44 GMT -5
caryc, Well you got half the story correct and it has been covered before. If you have the newer BFR with a serial number starting JT then this is correct, and you can't interchange gripframes with superBlackhawks ether as the angles are wrong and wont even bolt up. If on the other hand you have the older Pre JT BFRs, there gripframes are the same as a stainless Superblackhawk and you can use grips made for Ruger SBHs and will interchange with ruger grip-frames including Bisleys,Blackhawks, hunters, and superblackhawks. Here is an older picture of some of my BFRs, yes I'm a fan and yes I have made Bisley gripfames for new JT BFR's. it takes welding and milling.
|
|
|
Post by Lee Martin on May 25, 2011 15:05:25 GMT -5
and yes I have made Bisley gripfames for new JT BFR's. it takes welding and milling. Fun process, wasn't it? I swear we'll never do it again. -Lee www.singleactions.com
|
|
|
Post by bigbores on May 25, 2011 15:26:27 GMT -5
and yes I have made Bisley gripfames for new JT BFR's. it takes welding and milling. Fun process, wasn't it? I swear we'll never do it again. -Lee www.singleactions.comWhats funny is I hated doing it, but now I kinda want to do another one, I was thinking about buying a uberti bisley backstrap for a 1873 cattleman, and cutting and welding up the BFR front to make a BFR #5.
|
|
|
Post by Lee Martin on May 25, 2011 15:48:20 GMT -5
That would be neat. Sounds like a lot of work, but interesting idea. I also like the gripframe extension Jack Hunington does. May send my 475 backstrap out to him for that treatment. -Lee www.singleactions.com
|
|
|
Post by boxhead on May 26, 2011 8:16:44 GMT -5
A Harton slimmed Huntington grip frame and grips. Much better after than as supplied by Huntington which was way too chubby.
|
|
|
Post by bigbores on May 26, 2011 13:27:27 GMT -5
That would be neat. Sounds like a lot of work, but interesting idea. I also like the gripframe extension Jack Hunington does. May send my 475 backstrap out to him for that treatment. -Lee www.singleactions.comLee, With your skills I'm surprised you don't just weld a small slightly oversized plate to the bottom of your gripframe, mill everything flush, profile it a bit to make every thing look good then send the lengthened gripframe to your favorite grip maker.
|
|