Bowen Rough Country rear sight tested
Mar 9, 2024 19:37:33 GMT -5
bushog, mcquade, and 2 more like this
Post by bigbrowndog on Mar 9, 2024 19:37:33 GMT -5
You know how folks make claims and they sound awesome but too good to be true. Well I pulled a bone head move today, I was out driving a ranch and noticed a worker on a tractor brush chopping some young mesquite. He was in the other side of a 4 strand barbwire fence, and I was about to check loads in my double rifle. I wanted him to know I would be shooting but not in his direction so don’t be concerned. I wear my Bowen SRH 500L in a Randy Miller chest rig, and knew it would be tough slipping through strand 2 and 3 while wearing the rig.
So I took it off and placed it on the hood of my little ranch truck. I figured the hood would allow me to see it and remind me to grab it. I slipped somewhat easily through the two strands. Spoke with the gentleman and proceeded back across. I was In A hurry as daylight was fading fast and I had several loads to test. Got in the drivers seat did a nifty 3 point reverse turn around and just glimpsed something slide off my hood as I caught third gear in my rush to get to shooting. By the time I stopped I was 20-30 feet away and not too terribly worried as the gun is stainless and the holster “kinda” protected it,….i thought.
When I picked it up there was dirt and grass shoved into the holster, the cylinder gap, the cylinder rear face, and dirt and grass shoved down into the rear sight, screws, and gaps under the sight and in between where it sits in the topstrap. I had to take a knife blade and clean out the windage screw slots, clean out the gap under the sight base and clean out dirt and grass from the elevation adjustment screw, and clean out where the rear sight blade face slides left and right. I was pissed at myself for forgetting about it and relieved that no apparent damage had been done to the notch or rear blade.
i went and shot it to verify zero and it was still zeroed, still tight, and no dents or dings to catch light. It is Texas pasture, Toyota hood, tested tough.
thanks Hamilton, it’s a nice sight……….Oh, and Randy your holster kept the gun snug and safe without unlatching the strap and stud attachment, all my holsters will be fitted this way from now on, you make good stuff too my friend
Trapr
So I took it off and placed it on the hood of my little ranch truck. I figured the hood would allow me to see it and remind me to grab it. I slipped somewhat easily through the two strands. Spoke with the gentleman and proceeded back across. I was In A hurry as daylight was fading fast and I had several loads to test. Got in the drivers seat did a nifty 3 point reverse turn around and just glimpsed something slide off my hood as I caught third gear in my rush to get to shooting. By the time I stopped I was 20-30 feet away and not too terribly worried as the gun is stainless and the holster “kinda” protected it,….i thought.
When I picked it up there was dirt and grass shoved into the holster, the cylinder gap, the cylinder rear face, and dirt and grass shoved down into the rear sight, screws, and gaps under the sight and in between where it sits in the topstrap. I had to take a knife blade and clean out the windage screw slots, clean out the gap under the sight base and clean out dirt and grass from the elevation adjustment screw, and clean out where the rear sight blade face slides left and right. I was pissed at myself for forgetting about it and relieved that no apparent damage had been done to the notch or rear blade.
i went and shot it to verify zero and it was still zeroed, still tight, and no dents or dings to catch light. It is Texas pasture, Toyota hood, tested tough.
thanks Hamilton, it’s a nice sight……….Oh, and Randy your holster kept the gun snug and safe without unlatching the strap and stud attachment, all my holsters will be fitted this way from now on, you make good stuff too my friend
Trapr