fre3
.240 Incinerator
Posts: 82
|
Post by fre3 on Apr 28, 2023 6:51:27 GMT -5
Looking for anyone that can make some nice ones for a CZ52?
|
|
|
|
Post by potatojudge on Apr 28, 2023 10:52:27 GMT -5
|
|
|
|
Post by bigbrowndog on Apr 28, 2023 10:56:35 GMT -5
If you can send the existing grips to Zane, I’m sure he could put a set together for you. It would be worth contacting him.
Trapr
|
|
fre3
.240 Incinerator
Posts: 82
|
Post by fre3 on Apr 28, 2023 12:07:06 GMT -5
If you can send the existing grips to Zane, I’m sure he could put a set together for you. It would be worth contacting him. Trapr His number? |
|
|
|
Post by bigbrowndog on Apr 28, 2023 13:39:13 GMT -5
Contact him on here via messages, LSCG.
Trapr
|
|
|
|
Post by needsmostuff on Apr 28, 2023 15:02:25 GMT -5
These would be a nightmare to inlet by hand. I would go with the Hogue grips and not look back . I believe these are Hogue's but not 100% sure and no idea what wood they are made of. Still basic and plain, but better than the Bakelite they were born with.   |
|
|
|
Post by magpouch on May 3, 2023 20:58:18 GMT -5
|
|
gnappi
.375 Atomic
Posts: 1,537
|
Post by gnappi on May 9, 2023 7:37:02 GMT -5
I had Altamont make a set for me a few months ago never again...
I got the grips in from Altamont and I'm not one of those ninnies
that whine and crab over minor imperfections in craftsmanship or
wood grain, and demand a refund and that the builder / worker be
fired, but these grips were a surprise, and not a good one.
I bought them for a S&W "N" frame which as you all know has been in
production a pretty long time, so it really surprised me that their
CNC could have been coded so badly (or their machine is out of spec)
to have proud wood sticking into my middle finger to make them
unusable without modification.
OK, dremel here a bit and even though the finish needs touch up, it is
a disappointment but no REAL biggie. The real surprise was the
ferrules, BOTH sides are threaded and the screw (3 supplied for
different grip widths, good deal there) had to be used to re-thread
the entry ferrule to reach the other side!
I was going to order grips for a Ruger blackhawk and Vaquero, but I'll
look elsewhere now.
|
|
fre3
.240 Incinerator
Posts: 82
|
Post by fre3 on May 9, 2023 14:05:59 GMT -5
These would be a nightmare to inlet by hand. I would go with the Hogue grips and not look back . I believe these are Hogue's but not 100% sure and no idea what wood they are made of. Still basic and plain, but better than the Bakelite they were born with. What front sight is that? |
|
|
|
Post by needsmostuff on May 9, 2023 16:17:10 GMT -5
What front sight is that? Both front and rear were SIG sights with white dots ,,,,, I think maybe 226 but really don't remember. I put them on 10 years ago. Sure, can see them better than the thin, short factory ones. Rear one came really close to fitting as is. Front, of course had to cut a dovetail. Well worth the effort. |
|
