Post by boolitdesigner on Jun 27, 2019 15:46:05 GMT -5
MP Molds 432-245-WC Brass plain base Hollow Point or Solid Mold. This is a recreation of the older Lyman full wadcutter designs. It fits the usual 44 caliber revolvers. Offered bullet diameters will be 0.432" and 0.434"..... both will cast out about a half thousandth larger dependent on your alloy of choice.
We will need enough to make Miha's pin requirements. A concurrent GB is going on at CB to help with the required pin numbers It may be a long time.... be warned and no whining.
I am offering these choices: 2 or 4 cavity Brass PB HP or Solid and 6 cavity aluminum PB Solid.
Pins included are: For the Hollow Point Mold are 1) Large HP pin, 2) a smaller Penta HP pin, 3) Cup HP pin and 4) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Prices are what MiHec is using for all his other molds. I have a request for prices to check that out.
Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
Post your disguised e-mail address (imashooterATgmailDOTcom), mold choice, diameter wanted, number of cavities and the number of molds wanted (one to however many).
Sign up list:
1. bushog.....boo-haaa athot maildot com..... Two 4 cavity HP molds
2. bushog.....boo-haaa athot maildot com..... One 6 cavity Solid mold
3. DiamondD.....Diamondean at hotmail dot com..... One 2 cavity HP mold
We will need enough to make Miha's pin requirements. A concurrent GB is going on at CB to help with the required pin numbers It may be a long time.... be warned and no whining.
I am offering these choices: 2 or 4 cavity Brass PB HP or Solid and 6 cavity aluminum PB Solid.
Pins included are: For the Hollow Point Mold are 1) Large HP pin, 2) a smaller Penta HP pin, 3) Cup HP pin and 4) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Prices are what MiHec is using for all his other molds. I have a request for prices to check that out.
Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
Post your disguised e-mail address (imashooterATgmailDOTcom), mold choice, diameter wanted, number of cavities and the number of molds wanted (one to however many).
Sign up list:
1. bushog.....boo-haaa athot maildot com..... Two 4 cavity HP molds
2. bushog.....boo-haaa athot maildot com..... One 6 cavity Solid mold
3. DiamondD.....Diamondean at hotmail dot com..... One 2 cavity HP mold
