Post by boolitdesigner on Jun 22, 2018 8:25:42 GMT -5
MiHec 359 Hammer 2 or 4 Cavity Brass Cramer Plain Base or Gas Check Hollow Point mold.
This is a new boolit design (scaled down from the popular 462 Hammer). This will be suitable for any 38 Special, 357Magnum, 357 Max or any of the 35 caliber rifles. It will cast at about 0.359" dependent on your alloy. The weight is as shown on the drawing dependent on your alloy of choice. Meplat to crimp = 0.295".
We will need enough people to commit to this so Miha uses up 100 HP pins. We will run this until we get the number we need or more, then it is up to MiHec to decide when to make it......... be warned and no whining. There is a companion thread to this to run the numbers up faster on CB.
Pins included are: For the Hollow Point Mold are 1) Large HP pin, 2) Small HP pin, probably a penta, 3) Cup pin, 4) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Prices are what MiHec says they'll be. I'll have to check that out.
Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
Post your disguised e-mail address (imashooterATgmailDOTcom), mold choice (2 or 4 cavity), base style (PB or GC) and number of molds wanted (one to however many).
Sign Up List:
1. sheriff.....crittrcallrATsbcglobalDOTnet..... One 2 cavity GC mold
2. JSilva.....Silva_justinAThotmailDOTcom..... One 4 cavity PB mold
3. wheelguns.....haw1961ATliveDOTcom..... One 4 cavity GC mold
4. wheelguns.....haw1961ATliveDOTcom..... One 4 cavity PB mold
5. autodidact.....jbpaulATsuddenlinkDOTnet..... One 2 cavity GC mold
6. autodidact.....jbpaulATsuddenlinkDOTnet..... One 2 cavity PB mold
7. leftysixgun.....SchockleyATicloudDOTcom..... One 4 cavity GC mold
This is a new boolit design (scaled down from the popular 462 Hammer). This will be suitable for any 38 Special, 357Magnum, 357 Max or any of the 35 caliber rifles. It will cast at about 0.359" dependent on your alloy. The weight is as shown on the drawing dependent on your alloy of choice. Meplat to crimp = 0.295".
We will need enough people to commit to this so Miha uses up 100 HP pins. We will run this until we get the number we need or more, then it is up to MiHec to decide when to make it......... be warned and no whining. There is a companion thread to this to run the numbers up faster on CB.
Pins included are: For the Hollow Point Mold are 1) Large HP pin, 2) Small HP pin, probably a penta, 3) Cup pin, 4) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Prices are what MiHec says they'll be. I'll have to check that out.
Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
Post your disguised e-mail address (imashooterATgmailDOTcom), mold choice (2 or 4 cavity), base style (PB or GC) and number of molds wanted (one to however many).
Sign Up List:
1. sheriff.....crittrcallrATsbcglobalDOTnet..... One 2 cavity GC mold
2. JSilva.....Silva_justinAThotmailDOTcom..... One 4 cavity PB mold
3. wheelguns.....haw1961ATliveDOTcom..... One 4 cavity GC mold
4. wheelguns.....haw1961ATliveDOTcom..... One 4 cavity PB mold
5. autodidact.....jbpaulATsuddenlinkDOTnet..... One 2 cavity GC mold
6. autodidact.....jbpaulATsuddenlinkDOTnet..... One 2 cavity PB mold
7. leftysixgun.....SchockleyATicloudDOTcom..... One 4 cavity GC mold
8. ncrobb.....ncrobbATbellsouthDOTnet..... One 4 cavity PB mold
9. DiamondD.....Diamondean at hotmail dot com..... One 4 cavity GC mold
9. DiamondD.....Diamondean at hotmail dot com..... One 4 cavity GC mold
10. jan.....jnear79 at yahoo dot com..... One 4 cavity GC mold
11. mart.....marty dot weatherup at yahoo dot com..... One 4 cavity GC mold
12. wgg.....ggoodwin six three @ yahoo dot com..... One 4 cavity GC mold
13. 450ak.....siberianfiveohfiveatgmail.com..... One 4 cavity PB mold
14. ohnomrbillk.....William dot Kinderknecht (at) gmail (dot) com..... One 4 cavity PB mold
15. ohnomrbillk.....William dot Kinderknecht (at) gmail (dot) com..... One 4 cavity GC mold
16.
12. wgg.....ggoodwin six three @ yahoo dot com..... One 4 cavity GC mold
13. 450ak.....siberianfiveohfiveatgmail.com..... One 4 cavity PB mold
14. ohnomrbillk.....William dot Kinderknecht (at) gmail (dot) com..... One 4 cavity PB mold
15. ohnomrbillk.....William dot Kinderknecht (at) gmail (dot) com..... One 4 cavity GC mold
16.
