|
|
Post by medicdave on Aug 8, 2017 0:52:48 GMT -5
Got one in and it too will need a little tweaking to be right. Grip frame is off center a bit, but looks to be the same amount shy as proud so should be able to get close recentering. It does dress up nice on mock up though......  |
|
|
|
Post by barbarosa on Aug 8, 2017 19:44:07 GMT -5
Medicdave, where did you obtain the front sight?
Thanks,
Barbarosa
|
|
|
|
Post by cherokeetracker on Aug 8, 2017 20:02:12 GMT -5
Yeah Dave, you have added your touches to this already,,,,, That is one cool look there.
|
|
|
|
Post by hughree on Aug 8, 2017 20:06:48 GMT -5
Wow! That wins the prize.
|
|
|
|
Post by medicdave on Aug 9, 2017 1:43:11 GMT -5
It's a 22/45 sight from Dawson Precision.100 wide, .495 tall. $19 shipped, can't beat that.  It DOES NOT fit as bought as the barrel contour is much to large to mate cleanly to the single six as bought. You can see above where it's not tight to the barrel on the sides. The base is also a bit thinner than stock so the mounting screw will need to be shortened a couple threads. Plan is to wrap a barrel in sand paper and lap the sight base down to match the single six contour. I believe it will also be much to tall, but I won't mess with the height untill later as I'm pretty sure this one is going to end up some flavor of 22 centerfire.  |
|
f3
.30 Stingray
Posts: 412 
|
Post by f3 on Aug 13, 2017 0:36:15 GMT -5
Grip fit is poor on mine,but it is purty. Haven't even shot it yet but contemplating buying another because at $385 its a steal. Looks like Davidsons website is down right now for maintenance.
|
|
|
|
Post by bullseye on Sept 3, 2017 21:15:39 GMT -5
My blued model arrived Thursday & I'm quite pleased. Fit and finish is superb but the grip frame was obviously ground with the frame but installed slightly off center, a common occurrence with Ruger revolvers, and easily fixed during the first spring change/tune up. BC gap is a decent .005 the throats aren't as ridiculously oversized as the last Single Six I purchased. Also the bore cylinder alignment is unusually good for a factory revolver when checked with a range rod. All in all I'm please but am also hoping Ruger produced just enough of these that they feel obligated to release some replacement parts, Particularly Single Six Bisley hammers...My fingers are crossed!
|
|
GSSP
.30 Stingray
Posts: 141
|
Post by GSSP on Sept 3, 2017 23:24:32 GMT -5
OOOOHHHHH, you guys are getting me in trouble. Didn't realize their was a Ruger Bisley 22 model. Went to Davidson's and just ordered one. At least as an FFL I get my own dealer pricing.
|
|
GSSP
.30 Stingray
Posts: 141
|
Post by GSSP on Sept 3, 2017 23:29:14 GMT -5
Wait! Their is a SS Bisley 22? I didn't find it on the Davidson's website. What is the SKU #. Maybe I missed it on the Davidson's site.
|
|
|
|
Post by Encore64 on Sept 4, 2017 0:40:17 GMT -5
Wait! Their is a SS Bisley 22? I didn't find it on the Davidson's website. What is the SKU #. Maybe I missed it on the Davidson's site. If I remember correctly, the blued guns were available through Davidson's and the stainless through SportSouth. |
|
|
|
Post by lshines on Sept 4, 2017 8:30:11 GMT -5
Y'all have driven me to searching and now pleading w the LGS but we haven't turned up anything. Please relieve my angst and tell me where I can order a SS!
|
|
|
|
Post by lshines on Sept 4, 2017 8:31:56 GMT -5
The LGS said they contacted Sports South and we're told not available
|
|
|
|
Post by bullseye on Sept 4, 2017 8:36:10 GMT -5
They only made 100 of each blued & stainless...Most likely there all sold out by now. Might keep an eye on the used market.
|
|
GSSP
.30 Stingray
Posts: 141
|
Post by GSSP on Sept 4, 2017 9:42:19 GMT -5
Just looked at SportsSouth and they have zero/0 in stock. Dang it!
|
|
|
|
Post by Encore64 on Sept 4, 2017 11:00:28 GMT -5
Sorry to say fellows, but I cut deeply into that stainless stock. They put them on for $375 and I loaded up for project base guns.
I can't have a frame converted to Bisley for that amount.
|
|
