|
Post by matt56 on Dec 14, 2020 17:32:58 GMT -5
I want to retrofit a jet ski engine into a jon boat.
Oh wait you mean custom guns...
|
|
|
Post by mike454 on Dec 14, 2020 17:39:44 GMT -5
Have a Horvath custom flattop target USFA at the engravers that I'm looking to have finished up and another USFA and S&W 58 that I'd like to have Andy do some work on. Not sure I'll see them in '21 but hope springs eternal.
|
|
|
Post by bushog on Dec 14, 2020 18:07:20 GMT -5
|
|
|
Post by mike454 on Dec 14, 2020 20:57:14 GMT -5
Just got a picture of my cylinder from the engraver, Been a long wait, but I'm getting excited!
|
|
|
Post by Encore64 on Dec 14, 2020 21:01:37 GMT -5
Absolutely Beautiful...
|
|
|
Post by bigbore5 on Dec 14, 2020 21:06:37 GMT -5
What's your Custom Plans for 2021? 2) Recreating The Matthes Lion Hunter, but in 32-20... Tthe grips would be the most expensive part, but they were special indeed. My plans are the missus' 41mag and a single six shop keeper for myself.
|
|
|
Post by Thunderjet on Dec 14, 2020 21:44:50 GMT -5
Instead of more I plan on making my currently owned revolvers better. Next year I will send both of my Bisley BFR's (475 and 500 JRH) back to MR for a wide spur trigger and an action job. If by some strange turn of fate they decide to sell the hammers then they will both go to Jack Huntington for the same work as well as custom fitted wood grips.
|
|
|
Post by dougader on Dec 15, 2020 12:09:57 GMT -5
Just got a picture of my cylinder from the engraver, Been a long wait, but I'm getting excited! That looks really nice. Who is doing the work for you?
|
|
|
Post by magman on Dec 15, 2020 12:35:09 GMT -5
Have a Ruger Bisley 44 mag 3 3/4 inch revolver that I want rebarreled. Tried a couple different smiths and they turned the job down. Guess it will go to Bowen, not that this is a bad thing.
|
|
|
Post by pacecars on Dec 15, 2020 13:35:22 GMT -5
I am thinking about a full lug 5 inch barreled S&W Model 25 cut for moon clips to use .45 Colt, .45 ACP and .460 Rowland with some nice engraving and a case hardened frame
|
|
|
Post by crash87 on Dec 15, 2020 13:44:32 GMT -5
Have a Ruger Bisley 44 mag 3 3/4 inch revolver that I want rebarreled. Tried a couple different smiths and they turned the job down. Guess it will go to Bowen, not that this is a bad thing. Care to elaborate on the reason why? I to had work turned down, just curious I guess crash87
|
|
|
Post by kings6 on Dec 15, 2020 14:44:09 GMT -5
The only thing for 2021 is wrap up a couple that are still out then continue to fine tune to few back to my original Quest idea. I am still on the fence about what to do with Roy Fishpaws old model 41 as far as barrel goes and holes in the top strap.
|
|
|
Post by mike454 on Dec 15, 2020 17:36:03 GMT -5
Just got a picture of my cylinder from the engraver, Been a long wait, but I'm getting excited! That looks really nice. Who is doing the work for you? Thanks! Brian Powley is the engraver
|
|
|
Post by magman on Dec 15, 2020 17:56:57 GMT -5
Have a Ruger Bisley 44 mag 3 3/4 inch revolver that I want rebarreled. Tried a couple different smiths and they turned the job down. Guess it will go to Bowen, not that this is a bad thing. Care to elaborate on the reason why? I to had work turned down, just curious I guess crash87
|
|
|
Post by magman on Dec 15, 2020 17:58:51 GMT -5
The one said he didb't have time. Really odd, I didn't even ask for time didn't ask for a timeframe.
The second never gave a reason
|
|