|
Post by vashooter on Dec 9, 2014 13:06:25 GMT -5
I just ordered a Accurate mold 31-120s and I'm wondering if any one has any source of load data for 120 gr bullets all my data goes up to 115 gr. I do not expect you to give me charge weights but any printed data would help Thanks
|
|
wdr2
.30 Stingray
Posts: 147
|
Post by wdr2 on Dec 9, 2014 13:16:23 GMT -5
sending you a PM
|
|
|
Post by vashooter on Dec 9, 2014 13:31:04 GMT -5
PM returned Thanks
|
|
|
Post by 2 Dogs on Dec 9, 2014 14:18:51 GMT -5
We are running 11.6 grains of H110 on Corders 125 grain GC bullet. We are seeing one inch groups at 25 yards. YYMV depending on how much your bullet intrudes into the case capacity.
Please let us know your results.
|
|
|
Post by vashooter on Dec 9, 2014 14:41:28 GMT -5
Thanks 2 dogs I will keep you all posted on my results
|
|
|
Post by williamiorg on Dec 11, 2014 21:33:36 GMT -5
I just got an email from Accurate - my mold is ready to ship. This is a two cut mold so that is fast work. You ordered before I did. Is yours shipping?
|
|
|
Post by vashooter on Dec 15, 2014 6:44:22 GMT -5
Yes got mine on Saturday it looks great I have not started casting yet hopefully this week. I will keep you all posted
|
|
|
Post by vashooter on Dec 17, 2014 6:58:47 GMT -5
I fired up the pot and did a little casting last night and that accurate mold is wonderful the 31-120s fits the single 7 cylinder perfect can't wait to cast some more and get to loading and shooting
|
|
|
Post by Encore64 on Dec 17, 2014 8:19:24 GMT -5
Please keep us updated...
|
|
|
Post by vashooter on Dec 29, 2014 13:38:39 GMT -5
I should be able to get some range time in on sunday I loaded up some 120 grainers last night with 7.0 grs of power pistol and 4.7 grs of universal. I can not find any H110 but I think I saw some where that W696 is the same as H110 I will have to make sure I know where there is some W296 I will keep you up dated
|
|
|
Post by vashooter on Jan 19, 2015 8:37:31 GMT -5
Well I finally got to shoot my handloads.The accurate mold 31-120s did very good with Power Pistol going around 1200 fps groups under 1 inch at 25 yards on sand bag rest. Same with W-296 I had some similar loads but using the Lyman 311008 and did not get the sub 1 inch groups but they were not bad. I think the 31-120 mold was made for the single Just got the new handloader mag going to try some of the loads in the article.
|
|
|
Post by vashooter on Jan 19, 2015 8:43:35 GMT -5
I forgot to mention I shot over 100 rounds and did not have any issues with the base pin that I have heard others having.
|
|
|
Post by williamiorg on Jan 19, 2015 16:15:18 GMT -5
I went ahead and ordered three Wolfe base pin springs as I do have the problem with my 44 Spl Bisly and heavier bullets. When loaded below 1,000 fps which is where I should stay for my best shooting, I do not have the problem.
|
|
|
Post by vashooter on Jan 26, 2015 7:51:05 GMT -5
Well I spoke too soon took the single 7 out yesterday and started having issues with my base pin. I guess I will have to order one any suggestions Belt mountain I figure
|
|
|
Post by Encore64 on Jan 26, 2015 9:06:46 GMT -5
I put blt mtn in all three of mine. Works fine.
|
|